DH56 Series Offset Disks
- Working widths range from 10-ft. to 14.5-ft.
- Up to 868 Lb. of cutting force per blade
- Large gang axles for strength
- Oil bath tapered roller bearings minimize maintenance
Features
Adjustable disk blade scrapers increase productivity
Scrapers clean disk blades
Scrapers work great in wet and sticky soils
Adjustable disk blade scrapers keep disk blades clean and performing in wet and sticky soils for increased productivity.
End washers and wrenches keep gang shaft end nut tight
Keeping gangs tightened increases wear life
Gang nut wrenches are always there when needed
End washers help keep the gang shaft end nut tightened during operation, increasing gang wear life.
Two gang nut wrenches are supplied with each unit and securely attached to the unit, ready to use when the gangs need tightening.
Transport locks secure disk wings
Transport locks secure disk wings cylinder
Transport locks are standard, ensuring disk wings are in secure transport mode.
Two separate control arms create consistent performance
Control arms level in ground and during transport
Easy to set for desired soil condition
Two separate control arms are standard, one for transport leveling and one for leveling while the disk is in the ground. Once set for a given soil condition, the disk will continue to perform with consistency.
Oil bath tapered roller bearings minimize maintenance
Minimal maintenance increases work hours
Sealed with industrial-grade seals
Oil bath tapered roller bearings, sealed with industrial-grade seals, keep maintenance to a minimum and profitable working hours at a maximum. The bearings come complete with a wear plate.
Specifications
Specs & Compare
Add Model
| Specs & Compare | ||||
|---|---|---|---|---|
| Select up to 4 models to compare specifications | John Deere DH56 Series Offset Disks |
Transport
| Width | 3.4 m 11 ft |
|||
|---|---|---|---|---|
| Ground clearance with base blades | ||||
| Wheel hub bearings | Dual tapered roller bearings | |||
| Height | ||||
| Length |
Working
| Approximate working width | 3 m 10 ft |
|||
|---|---|---|---|---|
| Maximum penetration |
Weight
| Net | 6,304.9 kg 13,900 lb |
|||
|---|---|---|---|---|
| Weight per disk blade | 393.7 kg 868 lb |
Tractor requirements
| Recommended PTO hp range | ||||
|---|---|---|---|---|
| Recommended drawbar hp range | 167.8 kW 225+ hp |
Frame
| Type | Single offset rigid | |||
|---|---|---|---|---|
| Duty | Heavy | |||
| Tube size | 20.3x20.3x1.3 cm 8x8x0.5 in. |
Hitch
| Front hitch type | Pintle | |||
|---|---|---|---|---|
| Bolt-on rear hitch |
Disk blades
| Spacing | 43.2 cm 17 in. |
|||
|---|---|---|---|---|
| Quantity | 16 | |||
| Type | Notched (front) Notched (rear) Standard |
|||
| Blade concavity |
Available blade sizes
| Blade option one | 914x12.7 mm 36x0.5 in. |
|||
|---|---|---|---|---|
| Blade option two | ||||
| Blade option three | ||||
| Blade option four | ||||
| Blade option five | ||||
| Blade option six |
Disk gangs
| Front angle | 3 positions | |||
|---|---|---|---|---|
| Rear angle | 3 positions | |||
| Furrow fillers | ||||
| Axle size | 6.4 cm 2.5 in. |
|||
| Axle material | Round heat treated alloy steel threaded on both ends | |||
| Bearing type | Oil bath tapered roller | |||
| Bearing wear plates | Standard | |||
| Bearing standards | Welded, reinforced | |||
| Scrapers | Adjustable |
Lighting and safety
| Markings | SMV | |||
|---|---|---|---|---|
| Safety tow chain | Yes | |||
| Lights | Yes |
Tires
| Type | 2 - Radial Industrial | |||
|---|---|---|---|---|
| Size | 385/65R22.5 | |||
| Wheel hub type | 5-spoke Dayton hubs |
Set-up time
| Labor hours | For two people: 2-3 hours |
|---|
Warranty
| Time period | 1 year |
|---|
Additional information
| Date collected |
|---|
Key Specs
| Approximate working width | ||||
|---|---|---|---|---|
| Disk blades | ||||
| Frame | ||||
| Notched (front) Notched (rear) | ||||
| Recommended drawbar hp range | ||||
| Transport - Width |