XUV865R Crossover Utility Vehicle

The Gator™ XUV Crossover Series Utility Vehicle has a precision-engineered drivetrain system that fully utilizes engine power, optimizing acceleration, hauling, towing, and hill-climbing capabilities. Power is transmitted from the engine through a continuously variable clutch system to the transaxle.

Key elements of the drive system include:

Variable-speed drive

Variable-speed drive

The variable-speed drive consists of two clutches and a drive belt:

• Drive clutch is attached to the engine.
• Driven clutch is attached to the transaxle.

Features include:

• The engine braking system utilizes a tight belt for operation, requiring an idler sleeve on the primary clutch for neutral. The secondary clutch is a build-on-shaft design that utilizes a cam to tune the acceleration and deceleration of the vehicle. The clutch will stay engaged, providing deceleration until approximately 5 km/h (3 mph).
• The continuously variable transmission (CVT) air intake draws in cool air to reduce heat and the amount of water ingestion into the CVT system. The system will reduce belt slippage and improve durability.
• A low- and high-speed forward gear offering:
  • Low range is 0 km/h to 40 km/h (0 mph to 25 mph), XUV835
  • Low range is 0 km/h to 24 km/h (0 mph to 15 mph), XUV865
  • High range is 0 km/h to 72 km/h (0 mph to 45 mph), XUV835
  • High range is 0 km/h to 45 km/h (0 mph to 28 mph), XUV865
• Ability to creep along slowly to maneuver in tight spaces
• Standard full-clutch enclosure with high speed fan provides longer belt and clutch life
• High-ratio clutches with three cam weights for maximum belt-clamp load in high torque conditions

NOTE: Delivery of torque to the ground and top speed depends on tire size, which is a function of nominal size and pressure.

How the variable-speed drive works:

1. As engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
2. As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
3. With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
4. The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts drive speed upward or downward so that engine rpm remains optimal.

Transaxle, mechanical front-wheel drive (MFWD), and constant velocity (CV) shafts

Side view of CVT intake and clutch enclosure

Differential lock switch and MFWD switch

Rear view of transaxle and CV shafts

CV boot protection

Operator interface features:

• Selectable four-wheel drive (4WD) system with a limited slip front differential and dash-mounted electronic rocker switch
  • Provides exceptional traction in challenging conditions
  • Near instantaneous torque to the front wheels once rocker switch is engaged
  • Maintains turf-friendly operation in two-wheel drive (2WD) mode
  • Combined with rear traction assist (differential lock), provides excellent traction in challenging conditions
  • More control descending hills with 4WD engaged as all four wheels help slow the vehicle down
    • Clutch engagement still necessary to prevent free coasting

Transaxle features:

• Low, high, neutral, reverse, and park transaxle
• Automotive-style, integrated park position in transmission
• Low range for maximum torque delivered to the wheels for hauling, pushing, and pulling
• High range for maximum vehicle speed
• To shift out of park, service brake must be pressed to release the parking solenoid. An audible click will be heard and allows the vehicle to shift out of park into the desired gear.

NOTE: Differential design reduces scuffing of the turf during turns because it allows the inside wheels to turn slower than the outside wheels.

• Start in gear, neutral, or park position for quick starting. The service brake must be engaged to start when in gear or neutral.
• Large, sealed bearings are located inside the housing for better protection and durability
• Contains gear case for transferring power to the MFWD
• Splined shaft interfaces for maximum torque transfer and durability
• All drive gears machined from highest grade gear steel
• Protected by a skid plate

MFWD features:

• Electronically selectable by the operator
  • Offers limited slip functionality for precision steering and great traction while pointing and shooting out of a corner.
• Vertically oriented oil drain for easy maintenance
• Protected by a steel skid plate and frame

Drive shaft features:

• Rear CV shaft diameter measures 27 mm (1.1 in.) and is designed for peak engine and braking torque
• Front CV shaft diameter measures 23 mm (0.91 in.) and is designed for peak engine torque
• Propshaft is designed for peak engine torque
• All CV shaft and propshaft joints are maintenance free and protected by exclusive thermoplastic elastomer (TPE) boots for durability

Heating, ventilation, and air conditioning (HVAC) dash shown

Whether it is a completely open operator station or a factory installed cab, the interior has been redesigned with comfort and ergonomics in mind.

• Gear shift control and differential switch on the dash

HVAC dash shown (R trim)

• Tilt steering

Tilt steering	Tilt steering (up position)	Tilt steering (down position)

• Bench seat with driver adjustment

Bench seat adjustment

• Three-wide seating

Seating

Cab

M cab door

R cab door

• Functioning door windows – roll up and down

Side windows and front window

Venting position

• Fully opening front window with vent position

Headliner shown on an M-trim open station (with optional windshield, wipers, rear panel, and side mirrors installed)

• Available interior roof headliner factory installed on M-trim cab units and M-trim heating, ventilation, and air conditioning (HVAC) cab units

Door sealing

• Automotive-style sealing

Styled roof (R roof shown)

• Styled roof with channels designed-in to move water to the outside edges

Front roof light

Rear roof light

• Molded-in pockets for front and rear light mounting
  • Keeps lights below the roof line for protection

Inner door handle

Outer door handle

• Easy-opening door handles and mechanisms

M-trim HVAC controls

• HVAC – if equipped

HVAC details

Automotive-style controls on the center of the dash - easy and convenient to reach for the operator or passengers

• Four dash vents
  • Adjustable louvers and face plates
• Windshield vents mounted on the top of the dash
  • Fast defrost
  • Efficient air flow
• Air filter on the passenger side of the cab at foot level
• Three fan speeds
  • 0: off
  • 1: low
  • 2: medium
  • 3: high
• Temperature adjustment knob
  • Counterclockwise for cooler temperature
  • Clockwise for warmer temperature
• Four air flow modes
  • Dash vents
  • Dash and floor vents
  • Defroster vents and floor vents
  • Defroster vents
• HVAC compressor on/off button
  • Pushing the button once turns the air conditioning on - indicator light illuminates blue
  • Push the button again to turn off the air conditioning
• Air flow constant with compressor on or off
• Turn compressor off for full engine power
• Gas machines have an idle bump to raise rpms to assist driving more power for the HVAC system
  • 1075 rpm in any gear at idle with air conditioning on
  • 1400 rpm when in neutral and the park brake is engaged
• HVAC - if equipped

HVAC controls and vents on the dash

854-cc (52.1-cu in.) diesel engine

The machine is powered by an 854-cc (52.1-cu in.), 3-cylinder, liquid-cooled, four-cycle diesel engine. It produces 48 Nm (35.5-lb-ft) of torque at 2600 rpm.

The advanced engine delivers superb starting, idling, and throttle response during operation.

The engine offers the following performance and reliability features:

• Indirect-injection diesel with glow plugs ensures fast starts in cold temperatures
• 17.1 kW (22.9 hp*) at 3600 rpm
• Overhead valve design for greater efficiency and fuel economy
• Spin-on oil filter for easy servicing
• Quiet operation through the entire rpm range
• Molybdenum-coated pistons
• High-stiffness cylinder block and gearcase
• High-flow water pump and optimized water jackets maintain a steady operating temperature and eliminate hot spots
• Full-pressure lubrication system
• In-line mechanical fuel pump
• Five-point, rubber isolated for quiet operation and minimal vibration
• Dry replaceable dual-element air cleaner with remote intake and a restriction indicator
• See-through coolant recovery tank permits the operator to check the coolant level without removing the radiator cap
• Open front grille allows proper air flow and ventilation to the radiator.

*The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. The actual operating horsepower will be less.

XUV front suspension detail

To complement the robust frame, the XUV is equipped with four-wheel independent suspension.

A dual A-arm front and rear suspension provides a smooth ride over challenging terrain and excellent hauling characteristics.

The entire suspension system has been optimized to handle cargo without compromising ride quality or vehicle stability.

M-trim cab units (factory installed) and R-trim units have heavy-duty front and rear shocks installed from the factory.

• A higher spring rate and higher preload force versus standard springs prevent the vehicle from sagging with a heavy payload.
• These heavy-duty shocks help with the heavier weight of the cab and when attachments are installed, like blades.

Dual A-arm independent front suspension features include:

• 200.7 mm (7.9 in.) of travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
• Heavy-duty nodular cast-iron knuckles support the constant-velocity (CV) shaft and wheel
• Maintenance-free rubber torsional A-arm pivots for long life and quiet operation
• CV shaft protection from sticks that may puncture the rubber boot
• Coil-over shocks absorb the most demanding terrain

XUV rear suspension detail

XUV rear suspension detail

Dual A-arm independent rear suspension features include:

• Unequal length and dual A-arm construction for superior wheel control and travel
• 231.14 mm (9.1 in.) of total travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
• Coil-over shocks absorb the most demanding terrain
• A-arms made from square/rectangular tubing reduce weight while remaining rigid
• Heavy-duty nodular cast-iron uprights support wheel loads with a double row of ball bearings
• CV driveshaft protection from sticks that may puncture the rubber boot
• Rear sway bar for lateral stability

Deluxe cargo box with optional light protectors

Top view of cargo box

The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust and dents and reduces noise.

Deluxe cargo box tailgate

Tailgate handle

Tailgate open

Tailgate lowered to 150 degrees

The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.

The standard-installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.

Deluxe cargo box tilt

Integrated handle for manual cargo box tilt

The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist.

A prop rod is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.

Integrated tie-down points

Integrated tie-down point in cargo-box bed

Additional tie-down points (TH 6X4 shown)

The deluxe cargo box offers integrated tie-down points for increased versatility. Tie-down points are located in the following areas:

• Four corners inside the cargo box bed
• Four points on the load guard directly behind the operator station (A)
• Tie-down bars on either side of the cargo box (B)
• Six points on the underside of the cargo box frame (circled)

Converting deluxe cargo box to a flatbed

XUV835 Cab shown

XUV835M Cab shown

Optional accessories for the deluxe cargo box:

• See attachment information in the Value Selling Navigator

Specifications

CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

On M- and R-trim vehicles, adding attachments and accessories is made easier by the inclusion of some main wiring harnesses that facilitate efficient hook-up.

Roof harness electrical port

Main vehicle harness – winch connection

If dual beam headlights are desired, the following bundles are required:

XUV835E/865E:

• BM26589 – dual beam LED headlights, including three-position rocker switch
• BUC10809 – front light harness kit
• BUC10810 – E-spec attachment harness

XUV835M/865M:

• BM26589 – dual beam LED headlights, including three-position rocker switch
• BUC10809 – front light harness kit

XUV835R/865R:

• BM26589 – dual beam LED headlights, including three-position rocker switch

This Gator™ XUV Crossover Utility Vehicle is equipped with power steering and a dual A-arm front suspension. These automotive-type systems exhibit excellent handling characteristics, as well as responsive steering and low steering effort:

• Steel ball-bearings secure the steering shaft and deliver smooth, responsive operation
• Completely sealed rack and pinion for long life
• Low steering ratio (lock-to-lock) provides more responsive steering and less operator input
• Shaft U-joints are phased for a smooth, uninterrupted motion of the steering wheel
• Tilt steering wheel with 15 degrees of travel

Electric power-assist steering system

Electric power-assist steering (EPAS) system has advanced features:

• Anti-kickback feature reduces the amount of steering unwinding when traversing difficult terrain.
• The system is speed-sensing and adjusts steering effort as the speed of the vehicle changes.
  • As speed increases, there is less steering assist for improved road feel.
  • As speed decreases, steering assist increases to give lower steering efforts for improved maneuverability.
• A warning/functional light on the instrument panel provides self-diagnostics and a warning light in the situation of no assist.
• Torque sensor measures steering wheel input so the on-board computer can provide the appropriate output for various driving situations.

With the EPAS system, the operator maintains a direct mechanical linkage from the steering wheel to the front wheels. The power steering system interfaces mechanically with the steering system by being inserted between the steering wheel and the rack-and-pinion assembly.

A differential torque sensor is integrated into the power steering assembly. The circuit board assembly is also integral with the power steering assembly.

Power steering does not reduce turning radius but significantly reduces steering effort by approximately 85 percent compared to models without power steering.

EPAS interface diagram

EPAS interface diagram

The numbered descriptions refer to the EPAS interface diagram shown above:

1. Torque sensor
2. Electronic control unit (ECU)
3. Fail-safe relay
4. Current/thermal control circuit
5. Reduction gears
6. DC motor
7. Rack and pinion
8. Function/warning light
9. Key power and ground
10. Vehicle speed sensor
11. Instrument cluster
12. Relay module

The R trim is cab only and comes with a tan interior and heating, ventilation, and air conditioning (HVAC) as standard equipment. Electrical wiring for increased flexibility for attachments also comes standard.

R-trim level tan interior

• Headliner is standard

Standard headliner

• Tan cloth 40/60 bench seat

Tan cloth bench seat

• Standard light-emitting diode (LED) headlights with high and low beams

LED headlight

• A and B post covers

Post cover	Post cover

• Rear panel cover

Rear panel cover

• Tan door panels

Tan door panels

• Interior rearview mirror

Rearview mirror

• Sun visors

Sun visor	Sun visor

• Dome light

Dome light

• Windshield wiper and washer

Windshield wiper	Windshield washer

Build-to-order options

• Available factory-installed winch on M- and R-trim units
• Available factory-installed brush guard
• Available factory-installed brush guard extensions
• Available factory-installed rear cargo box fender guards (rear bumper required, also factory installed)

StarFire™ 3000 Receiver installed on XUV835R

GreenStar™ display installed on XUV835R with optional phone and tablet mounts

The AMS integration kit allows the operator to mount a StarFire Receiver and GreenStar display (both receiver and display sold separately) to the Gator™ Utility Vehicle.

Key features of the AMS integration kit:

• Compatible with StarFire iTC, StarFire 3000, and StarFire 6000 Receivers
• Compatible with GreenStar 2 1800, GreenStar 2 2600, GreenStar 3 2630, and John Deere 4640 Universal Display
• Ability to mount receiver to the poly roof or on the occupant protective structure (OPS) alone

NOTE: Additional components are required to support the John Deere 4640 Universal Display include:

• AL212683 (1)
• 21M7577 (2)

Common applications:

• Boundary mapping
• Flagging field obstacles
• Soil sampling

Compatibility:

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements:

The back-up alarm kit alerts pedestrians when the Gator™ is operating in reverse:

• Includes alarm, mounting brackets, wire harness, and reverse switch (if not already installed)
• Conforms to SAE J994 performance specifications for a Type D alarm and is 89 dBA per the SAE specification (measured at 4 ft)

Cargo box pail holder

Cargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Cargo bed extender

Cargo bed extender

The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.

Deluxe cargo box bed mat

The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box divider located at rear of cargo bed

Cargo box divider located at front of cargo bed

Speedrail lock in the unlocked position

Speedrail lock in the locked position

The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.

Cargo box side extension kit

The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch. 

Product features include:

• Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m³ (26 cu ft)
• Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
  • Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
• Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
• Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
• Compatible with Gator cabs and bedliner

NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.

Rear fender flare kit on XUV865

Rear fender flare kit

A – Fender flare

B – Fender

The rear fender flare kit minimizes debris from reaching the operator station.

Product features include:

• Two pliable fender flares (one for each side)
• Hardware for mounting on the sides
• Compatible with all model year 2011 to current Gator™ XUV825, XUV825 S4, XUV855, XUV855 S4, XUV835, and XUV865 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles

Tool rack

Tool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detail

Adjusting the tool rack holder

Tool rack

Tool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detail

Adjusting the tool rack holder

Spare tire carrier

Spare tire carrier

Easily mount a spare tire to the side of the cargo box with this convenient kit.

Recommended to carry spare front tire, as the front tire can be mounted on either the front or rear hubs.

Shown in full up position

The Gator™ XUV Series can be equipped with an optional power lift for the cargo box. This is one of the most important accessories for increasing work efficiency. It is an excellent complement to these highly capable utility vehicles.

Key features

• Capable of lifting a maximum vehicle cargo box load of 454 kg (1000 lb)
• Lifts box to 49 degrees from horizontal for ease of service and cargo box load removal
• Quick horizontal-to-49-degree time
• Can be installed in minutes using the vehicle's prewired connectors and mounting points
• Compact design fits nicely around the transmission and linkages, providing full protection
• Fully sealed and weatherproof design does not require maintenance and is built for maximum durability
• Overload protection protects against misuse

Compatibility

• Model year 2018 to current XUV825 and XUV855 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Drawbar kit for receiver hitch

Description:

• Kit includes a 51-mm (2-in.) drawbar, 10-mm (0.39-in.) pin, and hair cotter pin
• Steel construction has a 25-mm (1-in.) ball hole size
• Can be mounted in the standard rear receiver hitch or the optional front receiver hitch
• Compatible with all Gator model year 2011-current XUV560, XUV560 S4, XUV590, XUV590 S4, XUV 625i, XUV 825, XUV 855, RSX860, and M-Gator™ A2 Utility Vehicles
• Compatible with HPX 615 and 815 Utility Vehicles
• Compatible with XUV 620i and XUV 850D Utility Vehicles

NOTE: Compatible with all Gator HPX Utility Vehicles if equipped with an optional 51-mm (2-in.) front receiver hitch. An optional 51-mm (2-in.) rear receiver is not available for the Gator HPX models. A 32-mm (1-1/4-in.) rear receiver hitch and drawbar are available for the Gator HPX models.

Left floor mat

Right floor mat

Key features

• Kit includes left and right floor mats
• Made from 8-mm (5/16-in.) thick textured rubber
• Tool-less install and easy removal for cleaning
• Helps further dampen operator station noise

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Hood rack

Hood rack (hinged forward)

Key features

• 124.5-cm (49-in.) long x 36-cm (14.25-in.) wide x 11-cm (4.25-in.) deep
• Welded steel tubing
• Design allows for convenient tie-down points to secure load
• 45-kg (100-lb) capacity

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Requires brush guard to be installed

Brush guard extensions

Brush guard extensions

Brush guard with extensions hinged forward

Brush guard with extensions

Key features

• Enhances the aggressive appearance of the vehicle
• Easily attaches to the brush guard (required – sold separately)
• Provides additional protection to the side hood and fender area without adding additional overall width to the vehicle
• Still allows full entry under the hood when brush guard is hinged forward

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cargo box fender guards

Key features

• Connects with rear bumper (required – sold separately)
• Provides enhanced styling in addition to heavy-duty protection to the side of the cargo box

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Front CV guards

Rear CV guards

Key features

• Kit contains both front and rear CV guards
• Additional added protection for the A-arms and CV joints
• High-strength, formed steel guards handle impacts while maintaining a low, unsprung mass to provide exceptional ride quality
• Easily bolts to the A-arms
• Drainage holes on the bottom of the guards prevent buildup of dirt, grass, and other loose materials

Compatibility

• Model year 2020 and newer XUV835 and XUV865 Utility Vehicles

Front fender guards - shown with brush guard (required) and brush guard extensions (optional)

Key features

• Easily attaches to the brush guard (required – sold separately)
• Provides protection to the front fender area
  • NOTE: With fender guards installed, the overall width of the vehicle increases to 1.75 m (69 in.).

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Rear bumper kit (TH 6X4 shown)

The rear bumper offers stylish, heavy-duty rear protection to the vehicle.

Compatible with:

• Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
• Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
• Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles

Rear CV guards

CV guards add additional protection for the A-arms, brake lines, and CV half shafts:

• Formed steel guards handle impacts while maintaining a low unsprung mass
• Easily bolt to the A-arms with six bolts
• Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
• Compatible with all model year 2011 to current Gator™ XUV625i, XUV825, XUV855, and M-Gator A2 Utility Vehicles
• Compatible with model year 2013 to current Gator XUV825 S4 and XUV855 S4 Utility Vehicles
• Compatible with model year 2018 to current Gator XUV835 and XUV865 Utility Vehicles

Rear-panel glass protector

Key features

• Provides protection to the cab rear-panel glass
  • NOTE: Never carry loads in the cargo box over the load guard.
• Perforated, black metal screen easily attaches to the cab rear panel (required – sold separately)

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Brake and taillight protector

The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.

Dash port harness connection

Dash port harness – lower connectors

Key features

• The front attachment harness (dash port) includes connections for the following kits:

• Rear sprayer
• Rear spreader
• Blades
• GreenStar™ Display as part of the Ag Management Solutions (AMS) integration kit

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Hydraulic blade and rear winch harness

Key features:

• The hydraulic blade and winch harness includes connections for the following kits:

• Hydraulic blade
• Winch

Compatibility:

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Horn

Horn switch

Key features

• Frequency: 410 Hz
• Sound pressure level: 100+ dB(A)
• Water-sealed type

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

Beacon light in up position

Beacon light in down position

Backlit beacon light switch

Key features

• 76-mm (3-in.) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
• Especially useful for working around properties and job sites
• Acrylic amber lens resists scratching and scuffing
• Impact-resistant nylon housing
• Society of Automotive Engineers (SAE) J845 (Class 3)-compliant
• UL® recognized
• Flash rate: 60 +/- 10 fpm
• Stands 21.3-cm (8.4-in.) tall from roof/occupant protective structure (OPS)
• Folds down out the way when not in use

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

UL is a trademark of UL LLC.

Front cab mounted

Rear cab mounted

Brush guard mounted

Key features

• The LED driving lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
• Beam pattern: driving (focused, intense beam of light good for illuminating a stretch of road directly in front of the vehicle)

Driving beam pattern – mounted on brush guard

Driving beam pattern – mounted on OPS/roof

• Lamp sealing: IP69K
• Light output (per light): 1150 lumens
• LED color temperature: 5000 K
• Amp draw (per light): 1.4 amps
• 6 LEDs per light
• Aluminum housing

Compatibility

• Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• HPX Utility Vehicles

Front cab mounted

Rear cab mounted

Brush guard mounted

Key features

• The LED work lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
• Beam pattern: flood (spread of light over a wider, shorter distance)

Flood beam pattern – mounted on OPS/roof

• Lamp sealing: IP69K
• Light output (per light): 1200 lumens
• LED color temperature: 5000 K
• Amp draw (per light): 1.4 amps
• 6 LEDs per light
• Aluminum housing

Compatibility

• Model Year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model Year 2018 to current XUV835 and XUV865 Utility Vehicles
• Model Year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• HPX Utility Vehicles

Side mirrors – open station

Side mirrors – open station

Side mirrors – cab door

Side mirrors – cab door

Key features

• Kit allows mirrors to be installed on either an open-station or cab vehicle
• Mirrors can be easily adjusted based on operator preference

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Accessory mounting bracket (shown with tablet and cell phone mount)

Key features

• Allows the cell phone and tablet mount to be installed in the upper dash location
• Required for cell phone mount if mounted in the lower dash location

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cell phones, global positioning system (GPS), and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator station.

RAM X-Grip holder

For proper machine operation, it is critical that accessory devices and tools be located and mounted where they are accessible but do not interfere with visibility and controls. The new RAM® mount kit has been specially developed to meet this need in John Deere tractors and now utility vehicles.

Simply remove the large wing nut from the assembly, insert the stud into any open hole in the occupant protective structure (OPS), and tighten down the jam nut.

Key benefits:

• Patented RAM X-Grip™ holder fits most cell phones and similar devices including iPod®, iPad®, iPhone®, BlackBerry®, Samsung Galaxy® and others.
• Mounts to the holes in the OPS
• Ball joints allow for variable positioning
• Holds firm even in rugged terrain
• The holder is compatible with many other RAM® products with their B size or 25.4-mm (1-in.) ball accessories

RAM X-Grip

The RAM X-Grip has a clean and clever four-leg design that sports great holding power without hiding the phone behind foam pads and plastic.

Features:

• Rustproof
• High-strength composite and stainless-steel construction
• Spring-loaded holder expands and contracts for custom fit
  • Minimum width: 1.875 in. (47 mm)
  • Maximum width: 3.25 in. (82 mm)
  • Depth: 0.875 in. (22 mm)
• Rubber-coated tips will hold device firm and stable
• Easy access grip knobs for quick release of your device

Warranty:

90 days, limited.

RAM and RAM X-Grip are trademarks of National Products Inc. iPad, iPod, and iPhone are trademarks of Apple, Inc. BlackBerry is a trademark of Research In Motion Limited (RIM). Samsung Galaxy is a trademark of  Samsung Electronics Co.

Tablet mount – upper mount location (shown with cell phone mount – sold separately)

Tablet mount – lower mount location (shown with cell phone mount – sold separately)

Key features

• Keeps tablet at the operator’s fingertips for doing jobs such as soil sampling
• Utilizes a RAM® mount to easily move tablet to desired location

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

RAM is a trademark of National Products, Inc.

Upper speakers

Subwoofer

Bluetooth® microphone

SiriusXM® Radio antenna/tuner

Key features

• Kit includes:
  • Wiring harnesses
  • SiriusXM® radio antenna/tuner (XM ready head unit required – sold separately)
  • Two 13.3-cm (5.25-in.) upper speakers
  • Subwoofer
  • Bluetooth® wireless microphone
• Jensen® speakers
  • Waterproof
  • 45-W root mean square (RMS) power each
  • 135-W peak power each
• Jensen subwoofer
  • Waterproof
  • 20.3-cm (8-in.) amplified subwoofer
  • Maximum power: 200 W
  • Aluminum mesh grille
  • Aluminum housing
• The head unit is sold separately through Parts. The operator must choose one of the following two head units to complete the stereo:
  • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM satellite radio, and Bluetooth technology
  • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth technology

NOTE: Must order head unit through Parts.

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Requires base radio kit

SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc. Jensen is a trademark of Electronics Trademark Holding Company LLC.

Lower left speaker

Lower right speaker

Head unit (sold separately) installed

Key features

• Kit includes:
  • Wiring harness
  • AM/FM antenna
  • Head unit mounting bracket
  • Two 13.3-cm (5.25-in.) speakers
• Jensen® speakers
  • Waterproof
  • 45-W root mean square (RMS) power each
  • 135-W peak power each
• The head unit is sold separately through Parts. The operator must choose one of the following three head units to complete the stereo:
  • SWJHD1130 – heavy-duty stereo with AM/FM, weatherband, and auxiliary input
  • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM® satellite radio, and Bluetooth® wireless technology
    • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.
  • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth wireless technology
    • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.

NOTE: Must order head unit through Parts.

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles

Jensen is a trademark of Electronics Trademark Holding Company LLC. SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc.

Wheel spacer kit

• The wider 26x12-12 tires, used in combination with four-wheel steering, on the X729, X739, and X749 Tractors do not allow adequate clearance for the tire chains, so the wheel spacer kit is required.
• Spacers simply bolt to the axle hub and the wheels to the spacer.
• BM22725 may also be used in all applications where the BM18021 wheel spacer kit has been used.
• BM22725 has additional hardware and an updated operator's manual compared to the BM18021 wheel spacer kit.
  • BM18021 was developed for use on the 400 Series (425, 445, and 455) Four-Wheel Steer Tractors for installing tire chains on the 4WS models when using 23x10.50-12 rear tires.
• The wheel spacer kit must be removed for use with the 54-in. (137-cm) Mower Deck on X700 Tractors.

Side-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Side-door opening toolbox features:

• 125-L (33-gal.) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Door can also be used as a work bench when down
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 – olive and black
• BM26219 – camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model Year 2018 and newer HPX615 and HPX815

Tailgate with brake lights and taillights

This tailgate kit with brake lights and taillights is specifically designed for compatibility with the top and side-door toolboxes (BM26162 and BM26160).

The tailgate can be installed in minutes once the toolbox and tail lights are installed by bolting them to the tailgate bracket.

Optional label kits are designed to fit with this tailgate:

• BM26220 – green and yellow
• BM26218 – olive and black
• BM26219 – camo

The tailgate is compatible with the following Gator™ utility vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model Year 2018 - current HPX615 and HPX815

Top-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Top door opening toolbox features:

• 125-L (33-gal.) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Toolbox divider
• Removable tool tray
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 –olive and black
• BM26219 – Camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model year 2018 and newer HPX615 and HPX815

Front turn signals

Rear signal lights (taillight protectors not included)

Hazards switch (top)

Turn signal switch (right)

Key features

• Kit includes:

• Front/rear turn signals
• Hazards
• Backlit switches

NOTE: Not intended for use on public roadways.

Compatibility

• Compatible with all model year 2011 to current Gator™ XUV825 and XUV825 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Compatible with all model year 2011 to current Gator XUV625i, XUV855, and XUV855 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

• Effectively anchors to trees/boulders
• Change the pulling direction
• Double the pulling capacity

The accessories kit includes:

• Flexible tree strap
• Snatch block
• Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

Cordura is a trademark of INVISTA.

2041-kg (4500-lb) winch (chassis mounted)

Plug-in remote

Key features

• Impressive pulling capacity of 2041 kg (4500-lb)
• Equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities
• Includes a 3.05-m (10-ft), water-resistant, plug-in remote for safe distance operation that plugs directly into the glove box
• 15.2 m (50 ft) of 5.6-mm (7/32-in.) synthetic rope with hawse fairlead
  • Synthetic rope does not develop sharp burrs like steel rope and does not store as much potential energy when under load
• Ergonomic clutch handle
• Limited lifetime, 3-year electrical (North America) warranty offered through WARN

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• M-spec and R-spec vehicles come from the factory winch ready, and no additional attachment harnesses are required
• Requires winch mounting kit to mount the winch either on the chassis or on the front or rear receiver
• Not compatible with winch mounts BM26252 and BM26393

Electrical harness requirements

WARN is a trademark of WARN Industries, Inc.

Wireless winch remote

Wireless winch remote mounted on XUV835

Key features

• Wirelessly control winch from up to 15 m (50 ft) away
• Weatherproof transmitter has two large buttons, making it easy to operate even while wearing gloves
• Colored light-emitting diode (LED) lights provide clear operator feedback
• Kit includes wireless transmitter, receiver, holster, wiring, and mounting hardware

Compatibility

• Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

2041-kg (4500-lb) winch (chassis mounted)

Key features

• Kit includes everything needed to mount the winch to the chassis

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.

2041-kg (4500-lb) winch (chassis mounted)

2041-kg (4500-lb) winch (mounted on rear receiver)

Key features

• Ability to mount the winch on the front or rear receiver
• Kit includes everything needed to mount the winch to the receiver

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.